Equipment and Electrical Appliances Lada Kalina 1

Electrical equipment: reference data
Table 13.1.1. Basic data for monitoring, adjustment and maintenance Table 13.1.2. Tightening torques for threaded connections Table 13.1.3. Lamps used in the vehicle * The number of lamps depends on...

itemprop="image"

Description of the electrical equipment system
The electrical network of the car is single-wire, the second conductor is the "ground" - the car body and the power unit. The negative terminals of sources and consumers of electrical energy are...

Checking the technical condition of electrical equipment
Recommendation. When searching for the causes of a malfunction of any electrical equipment, first make sure that its fuse is in good condition and that there is reliable contact in the connectors of...

itemprop="image"

Ignition Switch (Lock) — General Information
In the power supply circuit of most of the electrical equipment of the car, except for the emergency, sound and light alarms, interior lighting, parking lights, brake lights, security alarms and...

Ignition Switch (Lock) — Check
To complete the work you will need a multimeter. Sequence of execution 1. Prepare the vehicle for work and disconnect the wire terminal from the negative terminal of the battery (see " Preparing the...

Ignition switch (lock) — removal and installation
To complete the job, you will need four special bolts with breakaway heads. Note: If special bolts are not available, you can secure the new lock using M6 threaded bolts 20 mm long, although this...

itemprop="image"

Switches and Changeover Switches — General Information
The location and purpose of the switches installed in the instrument panel and in the floor tunnel trim are shown in Chapter " Controls and instrumentation ". In some vehicles, switches for heating...

Steering column switches — removal, inspection and installation
The steering column switches must be removed individually when checking and replacing them. Before disassembling the steering column and other similar work, it is advisable to remove the steering...

Switches on the central console of the instrument panel — removal and installation
The central console trim contains the hazard warning switch 3, the rear window heating switch 1 and the switch for the operating modes of the electric fan of the ventilation and heating system 2. To...

Reverse Light Switch — Removal and Installation
To carry out the work, you will need an inspection pit or overpass. Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the engine splash guard or...

Brake Light Switch — Removal and Installation
The brake light switch is located under the instrument panel on the brake pedal bracket. Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Disconnect the...

itemprop="image"

Control and measuring instruments and sensors
All the vehicle's control and measuring instruments: speedometer, odometer, tachometer, coolant temperature gauge, fuel gauge, and trip computer are installed on the instrument panel. The control...

Instrument cluster — removal, replacement of lamps and installation
Removal 1. Prepare the vehicle for work and disconnect the wire terminal from the negative terminal of the battery (see " Preparing the car for maintenance and repair "). 2. Having released the...

Low Brake Fluid Sensor — Checking and Replacing
Note: It is more convenient to check the sensor with an assistant. Examination 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Turn on the ignition. 3. Pressing...

Coolant Temperature Gauge Sensor — Checking and Replacing
To complete the work you will need: multimeter in ohmmeter mode with a measurement range from 0.1 to 10 kOhm; thermometer with a range of at least 100°C; a small heat-resistant container with a...

Oil Pressure Sensor — Replacement
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the decorative trim (see " Engine trim panel - removal and installation "). 3. Squeeze the...

Ambient Air Temperature Sensor — Replacement
The ambient air temperature sensor is installed behind the front bumper on the front panel of the body. Advice: You can make sure that the temperature sensor is working properly by comparing its...

itemprop="image"

Windscreen wipers and washers — general information
The vehicle is equipped with windshield and rear window wipers and washers*. The windshield wiper consists of a gear motor with rods and two levers with brushes. The supply voltage is supplied to the...

Windscreen wiper — removal and installation
Removal 1. Prepare the car for work and disconnect the terminal from the negative terminal of the battery (see " Preparing the car for maintenance and repair "). 2. Using a screwdriver, remove the...

Windshield Wiper — Motor Gear Replacement
Removal 1. Remove the windshield wiper from the car (see " Windscreen wiper - removal and installation "). 2. Mark or remember the position of the crank relative to the windshield wiper rods. 3....

Rear Window Wiper — Removal and Installation
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Lift the protective cover of the windshield wiper arm mounting nut. 3. Using a 10 mm open-end wrench,...

Windscreen Washer Pumps — Removal and Installation
You can check the serviceability of the windshield washer pump by applying 12 V voltage directly from the battery to its terminals. The faulty pump must be replaced. Removal 1. Prepare the car for...

Windscreen washer reservoir — removal and installation
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Disconnect the wire blocks from the windshield washer electric pumps, having previously marked the...

Windscreen washer nozzles — replacement
Warning. The injectors should only be removed in the manner shown below if they are being replaced, as this will break the retainers. If you need to remove the windshield washer nozzles without...

Car anti-theft system (immobilizer) — general information
The car is equipped with a standard anti-theft system (immobilizer) APS-6 with remote control. The system consists of an immobilizer control unit, a remote control unit, a remote control combined...

Immobilizer activation
Note: The immobilizer can be activated if the control system ECU has not previously undergone the immobilizer activation procedure. Warning. Activation must be performed only with the vehicle doors...

Remote Control — Battery Replacement
The remote control is powered by a CR2032 element. Press any of the buttons on the remote control. At this point, the indicator on the remote control should light up briefly. If the indicator does...

Immobilizer control unit — removal and installation
Removal 1. Prepare the car for work and disconnect the wire terminal from the negative terminal of the battery (see " Preparing the car for maintenance and repair "). 2. Remove the instrument panel...

Remote control unit — removal and installation
Removal 1. Prepare the car for work and disconnect the wire terminal from the negative terminal of the battery (see " Preparing the car for maintenance and repair "). 2. Raise the rear seat cushion....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Electrical equipment: Equipment and devices Lada Granta 1 (2011-2023, VAZ-2190)
• General information: Vehicle device Lada Priora 1 (2007-2018, VAZ-2170)
• Electrical equipment: Equipment and devices Lada Vesta 1 (2015-2023, VAZ-2180)
• General information: Vehicle device Lada Largus 1 (2012-2023)
• Electrical equipment: Equipment and devices Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code