Electrical equipment and appliances Lada Granta 1

Reference data on electrical equipment
Table 13.1.1. Basic data for monitoring, adjustment and maintenance Type of electrical equipment Direct current Electric car Single-wire - negative terminals of power sources and consumers are...

itemprop="image"

Lamps used in the car
Table 13.1.3. Lamps used in the vehicle Name of the lamp, installation location Number of lamps Lamp type According to GOST According to the EEC Headlights: - high and low beam lamp 2 AKG12-60+55 H4...

itemprop="image"

Description of the electrical equipment system
The car's electrical network is single-wire, the second conductor is the "ground" - the car body and the power unit are connected by the "ground" - the negative terminals of the sources and consumers...

Checking the technical condition of electrical equipment
Recommendation. When searching for the causes of a malfunction of any electrical equipment, first make sure that its fuse is in good condition and that there is reliable contact in the connectors of...

Mounting block — location of fuses and relays
Fuses and relays for switching on electrical equipment are installed in the mounting block. The fuse and relay mounting block is installed in the instrument panel on the left side. Fuse and relay...

Mounting Block — Replacing Fuses and Relays
Warning! Before replacing a fuse, you must determine and eliminate the cause of its blown fuse. To avoid failure of electrical equipment components, fuses with increased ratings or homemade ones must...

itemprop="image"

Ignition Switch (Lock) — General Description
In the power supply circuit of most of the electrical equipment of the car, except for the emergency, sound and light alarms, interior lighting, parking lights, and brake lights. security alarm and...

Ignition Switch (Lock) — Check
To complete the work you will need a multimeter. Sequence of execution 1. Prepare the car for work and disconnect the wire terminal from the negative terminal of the battery (" Preparing the car for...

Ignition switch (lock) — removal and installation
To complete the job, you will need four special bolts with breakaway heads. Note: If special bolts are not available, you can secure the new lock using M6 threaded bolts 20 mm long, although this...

itemprop="image"

Control and measuring instruments and sensors
All the vehicle's control and measuring instruments: speedometer, odometer, tachometer, fuel gauge, as well as the trip computer display are installed on the instrument panel. The control lamps are...

Instrument cluster — removal and installation
Removal 1. Prepare the car for work and disconnect the wire terminal from the negative terminal of the battery (" Preparing the car for maintenance and repair "). 2. Having released the steering...

Low Brake Fluid Sensor — Checking and Replacing
Note: It is more convenient to check the sensor with an assistant. Examination 1. Prepare the car for work (" Preparing the car for maintenance and repair "). 2. Turn on the ignition. 3. Pressing...

Oil Pressure Sensor — Replacement
Removal 1. Prepare the car for work (" Preparing the car for maintenance and repair "). 2. Squeeze the protrusions of the wire connector block on both sides and remove the block from the emergency...

itemprop="image"

Windscreen wiper and washer
The car is equipped with a windshield wiper and washer. The windshield wiper consists of a gear motor with rods and two levers with brushes. The supply voltage is supplied to the gear motor electric...

Windscreen wiper — removal and installation
Removal 1. Prepare the car for work and disconnect the terminal from the negative terminal of the battery (" Preparing the car for maintenance and repair "). 2. Using a screwdriver, remove the plug...

Windscreen wiper — motor-reducer replacement
Removal 1. Remove the windshield wiper from the car (see p. 173, " Windscreen wiper - removal and installation "). 2. Mark or remember the position of the crank relative to the windshield wiper rods....

Windscreen washer pump — removal and installation
You can check the serviceability of the windshield washer pump by applying 12 V voltage directly from the battery to its terminals. The faulty pump must be replaced. Removal 1. Prepare the car for...

Windscreen washer reservoir — removal and installation
Removal 1. Prepare the car for work (" Preparing the car for maintenance and repair "). 2. Disconnect the wiring blocks from the windshield washer electric pump, having previously marked the block...

Windscreen washer nozzles — replacement
1. Prepare the car for work (" Preparing the car for maintenance and repair "). 2. Open the hood. Note: If you have to replace the nozzle at a negative ambient temperature, before performing the next...

Car anti-theft system (immobilizer)
The car can be equipped with a standard anti-theft system (immobilizer) with remote control. The system consists of an immobilizer control unit, a remote control unit, a remote control combined with...

Immobilizer activation
Note: The immobilizer can be activated if the control system ECU has not previously undergone the immobilizer activation procedure. Warning! Activation must be performed only with the vehicle doors...

Remote Control — Battery Replacement
The remote control is powered by a CR2032 element. Press any of the buttons on the remote control. At this point, the indicator on the remote control should light up briefly. If the indicator does...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• General information: Vehicle device Lada Kalina Sedan (2004-2013, VAZ-1118)
• Electrical equipment: Equipment and devices Lada Priora 1 (2007-2018, VAZ-2170)
• Electrical equipment: Equipment and devices Lada Vesta 1 (2015-2023, VAZ-2180)
• Electrical equipment: Equipment and devices Lada Largus 1 (2012-2023)
• Electrical equipment: Equipment and devices Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code