Equipment and electrical appliances Lada XRAY 1

Central unit of body electronics of cars
Device, troubleshooting The work must be carried out in accordance with the requirements of the labor protection instructions for fitters in force at the enterprise. The central body electronics unit...

itemprop="image"

Functions of the Central Control Bureau of Vehicles
2.1. Starter control Power is supplied to the starter solenoid relay winding through the power contacts of the additional starter relay. The CBKE switches on an additional starter relay when the...

Diagnostics of the Central Body of Expertise of Vehicles
3.1. Parameters of the CBKE of LADA VESTA, LADA XRAY vehicles The parameters displayed by the Grade-X diagnostic tool in the "Signal Monitoring" mode and used to diagnose the CBKE functions are shown...

itemprop="image"

Error codes of the Central Control Module of cars
Error codes of the Central Control Module of cars Code malfunctions malfunction Conditions for conducting the test B1520-12 Starter relay - short circuit to power supply Control voltage is supplied...

Functional description and diagnostics of the EMM system
Description of the EMM system The purpose of this document is to describe the specification of the windshield wiper system and how it is controlled by the EMM. The architecture of windshield wiper...

itemprop="image"

Functions performed by the EMM system
This chapter describes all the functions that ensure the operation and control of the windscreen wiper system. For high speed, if the driver turns off "+APC" while the windshield wiper is operating,...

High Speed Switch CSW EMM System
2.1.1. Parameter: Automatic windscreen wiper operation at reverse speed: This function is provided by the cluster. This feature is only available for vehicles that have the "User Preferences"...

itemprop="image"

Low Speed Switch CSW EMM System
2.2.1. Parameter 4 02 05: Operation of windscreen wipers in automatic mode at reverse speed: Same as for high speed switch. 2.2.2. Description of the windshield washer operation: The BCM reads the...

itemprop="image"

EMM system failures
List of DTC codes Default code Default type Code name DTC REAR_WIPER_AUTOSTOP Error reliability signal REAR_WIPER_FAILURE 1.1.1 List of DTC codes Below are all DTCs for the front and rear wiper. Code...

itemprop="image"

Electrical equipment — design and operation features
The electrical equipment is made using a single-wire circuit - the negative terminals of the power sources and consumers are connected to the car body, which functions as the second wire. Nominal...

Battery — removal and installation
Removal Place the vehicle in the work area, apply the parking brake, turn off the ignition, and raise the hood. Attention! Before disconnecting the terminals from the battery terminals, it is...

Starter — removal and installation
Removal Place the vehicle on a two-post lift (electro-hydraulic lift type P-3.2 G with a lifting capacity of 3.2 t). Turn off the ignition, lift the hood, disconnect the ground wire terminal from the...

Generator — removal and installation
Technical characteristics of the generator TG 12C209 f. "Valeo": Maximum output current (at 14 V and 6000 min⁻¹), A — 120 Engine-generator gear ratio: 2.4 Generator type TG 12C209 f. "Valeo"...

Instrument cluster — removal and installation
Removal Place the vehicle in the work area, apply the parking brake, and turn off the ignition. Raise the hood, disconnect the ground wire terminal from the battery (spanner 10). Remove the steering...

Headlight corrector switch, electric mirror adjustment knob
Removal Place the vehicle in the work area, apply the parking brake, and turn off the ignition. Raise the hood, disconnect the ground wire terminal from the battery (spanner 10). Overcoming the...

Safe Parking System Elements — removal and installation
Purpose, composition and operating principle of the system The system is designed to detect obstacles located behind the vehicle and warn the driver of the distance to the obstacle using an acoustic...

Control and signaling unit for the secure parking system
Removal Place the vehicle in the work area and apply the parking brake. Raise the hood, disconnect the ground wire terminal from the battery (spanner 10). Open the trunk. Remove the two trim...

Elements of the multimedia and navigation system
Radio receiver and audio player, multimedia navigation equipment The car is equipped with a radio receiver and audio player or multimedia navigation equipment. The operations for removing these radio...

Central body electronics unit (CBEU)
Removal Place the vehicle in the work area and apply the parking brake. Raise the hood, disconnect the ground wire terminal from the battery (spanner 10). Remove the instrument panel storage...

SVEOS («ERA GLONAS») unit — removal and installation
Removal Place the vehicle in the work area and apply the parking brake. Raise the hood, disconnect the ground wire terminal from the battery (spanner 10). Remove the instrument panel storage...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Electrical equipment: Equipment and devices Lada Kalina Sedan (2004-2013, VAZ-1118)
• Electrical equipment: Equipment and devices Lada Granta 1 (2011-2023, VAZ-2190)
• Electrical equipment: Equipment and devices Lada Priora 1 (2007-2018, VAZ-2170)
• Electrical equipment: Equipment and devices Lada Vesta 1 (2015-2023, VAZ-2180)
• Electrical equipment: Equipment and devices Lada Largus 1 (2012-2023)

Link to this section in various formats

TEXTHTMLBB Code