Brake system of car Lada XRAY 1

Anti-lock braking system ABS 9.1
Troubleshooting The work must be carried out in accordance with the requirements of the labor protection instructions for fitters in force at the enterprise. The anti-lock braking system (ABS) is...

itemprop="image"

ABS diagnostic trouble codes and parameters
Table 3 Code Description and diagnostics 401001 Failure in the front left EMC intake circuit 1 Replace GA ABS 401101 Failure in the front left EMC exhaust circuit 1 Replace GA ABS 401401 Failure in...

itemprop="image"

Error codes and parameters for performing ECU diagnostics
Table 4 - Error codes and parameters for performing ECU diagnostics Code Description and diagnostics 401001 Failure in the front left EMC intake circuit 1 Replace the ECU GA 401101 Failure in the...

itemprop="image"

Brake system — features of the device
General requirements Work must be carried out in accordance with the requirements of the "Intersectoral rules for labor protection in motor transport" POT RM-027-2003 and labor protection...

Vacuum brake booster with master cylinder and reservoir assembly
Removal Place the vehicle on the work post, apply the parking brake and turn off the ignition. Open the hood and disconnect the wires from the battery (spanner 10). Loosen the battery clamp bar...

Brake pedal with bracket assembly — removal and installation
Removal Place the vehicle on the work post, apply the parking brake and turn off the ignition. Open the hood and disconnect the ground wire terminal from the battery (spanner 10). Remove the steering...

Front brake pads — removal and installation
Attention! Replace brake pads as a set on wheels of one axle. Installation of brake pads from different manufacturers or different types on wheels of the same axle is not permitted. Removal Place the...

Front brake assembly — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the front wheel in...

Front brake disc — checking technical condition
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the front wheel in...

Front Brake Disc Cover — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the front wheel in...

Rear brake drum — checking technical condition
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the rear wheel in...

Rear Brake Pads — removal and installation
Attention! Replace brake pads as a set on wheels of one axle. Installation of brake pads from different manufacturers or different types on wheels of the same axle is not permitted. Removal Place the...

Rear Brake Wheel Cylinder — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the rear wheels in...

Handbrake lever — removal and installation, adjustment
Removal Place the vehicle on the work post, apply the parking brake and turn off the ignition. Remove the floor tunnel lining in accordance with the requirements of TI 3100.25100.20589. Disconnect...

Handbrake cable — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the floor tunnel lining...

itemprop="image"

Brake pipes — removal and installation
Attention! Brake pipes must not have any kinks, dents or other damage that could lead to depressurization of the brake system; brake pipes with the above defects must be replaced. Attention! It is...

itemprop="image"

Flexible brake hoses — removal and installation
Attention! Brake hoses must not have any cracks, cuts or other damage that could lead to depressurization of the brake system. Brake hoses with the indicated defects must be replaced. Attention!...

ABS hydraulic unit — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition. Open the hood and disconnect the ground wire terminal from the battery (electro-hydraulic lift type...

Front Wheel Speed Sensor — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Raise the vehicle to a height...

Rear Wheel Speed Sensor — removal and installation
Removal Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition (electro-hydraulic lift type P-3.2G with a lifting capacity of 3.2 t). Remove the rear wheel in...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Chassis (running gear): Brake system Lada Kalina Sedan (2004-2013, VAZ-1118)
• Chassis (running gear): Brake system Lada Granta 1 (2011-2023, VAZ-2190)
• Chassis (running gear): Brake system Lada Priora 1 (2007-2018, VAZ-2170)
• Chassis (running gear): Brake system Lada Vesta 1 (2015-2023, VAZ-2180)
• Chassis (running gear): Brake system Lada Largus 1 (2012-2023)

Link to this section in various formats

TEXTHTMLBB Code