Brake system of the car Lada Vesta 1

Basic data for monitoring, adjustment and maintenance
Table 13.1. Basic data for monitoring, adjustment and maintenance Brake fluid type DOT-4 Front brake disc: - nominal thickness, mm 22 - minimum permissible thickness, mm 19,8 - maximum permissible...

Description of the brake system design
Front brake mechanism: 1 - brake hose; 2 - bleed nipple; 3 - support; 4 - brake shoe guide; 5 - spring stops of brake shoes; 6 - hub; 7 - brake disc; 8 - brake shoe; 9 - Protective cover of the guide...

Checking the brake fluid level
Warning! If the work requires adding brake fluid, use only new fluid recommended by the manufacturer. Avoid spilling brake fluid or allowing it to come into contact with vehicle parts, especially the...

Checking the service brake system drive
1. Prepare the car for work (see " Preparing the car for maintenance and repair "). Recommendation. It is convenient to inspect pipelines and brake hoses on an inspection pit or overpass. 2....

Checking the front brake mechanism
To complete the work you will need a caliper. Sequence of execution 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the front wheel (see " Wheel...

Checking the rear brake mechanism
To complete the work you will need a caliper. Sequence of execution 1. Remove the brake drum (see " Rear brake drums - replacement "). Warning: To avoid the pistons falling out of the wheel cylinder,...

itemprop="image"

Checking the parking brake system
The stroke of the parking brake drive lever should be within 5-7 clicks of the locking mechanism. At the same time, the braking system must reliably hold the equipped vehicle on a 23% slope. Note: A...

Hydraulic brake drive — bleeding
The hydraulic drive of the brake system is bled after repairs related to a breach in the tightness of the brake system and if there is a suspicion of air entering the system. In the latter case, you...

Replacing brake fluid
We replace the brake fluid in the brake hydraulic drive in accordance with the maintenance regulations (see " Maintenance plan "). We perform the replacement in the same sequence as bleeding (see "...

Master Brake Cylinder — replacement
The need to perform work is determined during the inspection of the technical condition of the brake system (see " Brake system - checking technical condition "). Also, the main brake cylinder must...

Brake hoses — replacement
The need to perform work is determined during the inspection of the technical condition of the brake system (see " Brake system - checking technical condition "). To perform the work you will need a...

Brake pipes — replacement
The need to perform work can be determined during the inspection of the technical condition of the brake system (see " Brake system - checking technical condition "). To perform the work you will...

Front brake pads — replacement
The need to perform work is determined during the process of checking the technical condition of the brake system (see " Brake system - checking technical condition "). Brake pads must be replaced...

Front Brake Caliper — Removal, Repair and Installation
The front brake caliper is removed for replacement or repair if a leak appears through the piston boot or if the piston is seized. The need to perform work can be determined during the inspection of...

Front brake discs — replacement
The need to perform work is determined during the process of checking the technical condition of the brake system (see " Brake system - checking technical condition "). Warning! Brake discs are...

Rear brake drums — replacement
The need to perform work is determined during the process of checking the technical condition of the brake system (see " Brake system - checking technical condition "). Warning! We replace the brake...

Rear brake pads — replacement
The need to perform work is determined during the process of checking the technical condition of the brake system (see " Brake system - checking technical condition "). Warning! When the brake...

Wheel brake cylinder — replacement
The necessity of performing this operation should be determined during the process of checking the technical condition of the brake system (see " Brake system - checking technical condition "). To...

Parking brake — adjustment
The parking brake must be adjusted after replacing the drive cables, and also if the check (see " Checking the parking brake system ") revealed the need for adjustment. The parking brake lever travel...

Front Wheel Speed Sensor — replacement
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the front wheel (see " Wheel replacement "). 3. Disconnect the sensor wiring harness from the...

Rear Wheel Speed Sensor — replacement
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the rear wheel (see " Wheel replacement "). 3. In the luggage compartment, press the lock and...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Chassis (running gear): Brake system Lada Kalina Hatchback (2004-2013, VAZ-1119)
• Chassis (running gear): Brake system Lada Granta 1 (2011-2023, VAZ-2190)
• Chassis (running gear): Brake system Lada Priora 1 (2007-2018, VAZ-2170)
• Chassis (running gear): Brake system Lada Largus 1 (2012-2023)
• Chassis (running gear): Brake system Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code