Car engine power system Lada Vesta 1

Basic data for monitoring, adjustment and maintenance
Table 9.3.1. Basic data for monitoring, adjustment and maintenance Fuel (according to GOST R 51866-2002) "Premium Euro-95" Fuel tank capacity, l 55 Fuel module 845 000 8680 Fuel rail 2190-1139009...

Description of the power supply system design
Engine intake system 21129: 1 - inlet module; 2 - throttle assembly; 3 - air supply hose to the throttle valve; 4 - air filter; 5 - resonator (air intake system muffler); 6 - electromagnetic valve of...

Power supply system — technical condition check
To perform the work you will need a special fuel pressure gauge. Sequence of execution 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the decorative...

Air filter — replacing the filter element
According to the manufacturer's recommendation, we replace the air filter element after every 30,000 km. Sequence of execution 1. Prepare the car for repairs (see " Preparing the car for maintenance...

Air filter — removal and installation
The operation may be required when repairing the engine and its systems. Therefore, in many cases it makes sense to remove the filter together with the mass air flow sensor or even the air supply...

Intake module — removal, replacement of gaskets, installation
Recommendation. The work is labor-intensive. In addition, the tight layout in the engine compartment makes it difficult to perform some operations. Access to the front intake module mount can be...

itemprop="image"

Fuel Line — Pressure Relief
Sequence of execution 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the fuel pump circuit fuse (see " Fuse and relay mounting block "). Note: You can...

Fuel rail — removal and installation
The fuel rail is dismantled to remove the injectors, as well as in other cases during engine repair. Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). We...

Fuel module — removal and installation
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Relieve the fuel pressure (see " Fuel Line - Pressure Relief "). Warning! After releasing the pressure,...

Fuel Module — Fuel Gauge Sensor Replacement
Recommendation. Malfunctions of the fuel level indicator sensor are most often associated with wear of the contact part of its rheostat. This can be verified by measuring its electrical resistance...

Fuel Module — Fuel Pressure Regulator Replacement
Recommendation. If you suspect that the pressure regulator is faulty, it must be replaced. Removal 1. Remove the fuel module (see " Fuel module - removal and installation "). 2. Disconnect the wire...

Fuel Module — Cleaning the Mesh Filter
Note: One of the reasons for low fuel pressure in the fuel rail may be a dirty mesh filter of the fuel module. Removal 1. Remove the fuel module (see " Fuel module - removal and installation "). 2....

Fuel Module — Fuel Pump Replacement
Recommendation. The operation of replacing the pump requires experience and accuracy (fuel module components may be damaged), therefore, in case of a fuel pump failure, it is recommended to replace...

Adsorber — removal and installation
The adsorber is installed under the front fender on the right. Sequence of execution 1. Prepare the vehicle for work and install it on an inspection ditch or overpass (see " Preparing the car for...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Power unit: Supply system Lada Kalina Sedan (2004-2013, VAZ-1118)
• Power unit: Supply system Lada Granta 1 (2011-2023, VAZ-2190)
• Power unit: Supply system Lada Priora 1 (2007-2018, VAZ-2170)
• Power unit: Supply system Lada Largus 1 (2012-2023)
• Power unit: Fuel system Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code