Doors, locks and windows of the car Lada Kalina 1

Replacing the trunk lid stops
To replace the trunk lid stops on your car, you will need a flat-blade screwdriver. 1. Pry up the spring clip... 2. ...and remove the trunk lid stop hinge from the pin. 3. Do the same with the second...

Removal, installation the trunk lid and adjusting its position
Helpful advice. The trunk lid is quite heavy and bulky, so it is recommended to remove and install it with the help of two people. To remove, install the trunk lid and adjust its position in the...

Replacing trunk lid hinges
To replace the trunk lid hinges on your car, you will need: a flat-blade screwdriver, 8 and 10 mm wrenches. 1. Remove the trunk lid support (see " Replacing the trunk lid stops "). 2. Remove the...

Removal, replacing and installing the trunk lid lock drive
The trunk lid lock drive is of a non-separable design and cannot be repaired. Replace the defective trunk lid lock drive. To remove, replace and install the trunk lid lock drive on a car, you will...

Removal, replacing and installing the trunk lid lock
The trunk lid lock is of a non-separable design and cannot be repaired. Replace the defective lock. To remove, replace and install the trunk lid lock on a car, you will need: a 10 mm spanner,...

Adjusting the position of the trunk lock retainer
If the trunk lid has vertical play in the closed position or closes with great effort, adjust the height of the trunk lid lock. To adjust the position of the trunk lock retainer on a car, you will...

Removal and installation the trunk lid trim
To remove and install the trunk lid trim on a car, you will need: an 8 mm spanner and a flat-blade screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the trunk...

Removal and installation the front door trim
To remove and install the front door trim on a car, you will need: a knife, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the...

Removal, installation and repair of the outer front door handle
The location of the lock, lock drive rods and front door handles is shown in the figure 10.2. To remove and install the outer handle of the front door on a car, you will need: a socket wrench "8",...

Removal and installation the front door central lock
To remove, replace and install the central lock of the front door on a car, you will need: a Phillips-head screwdriver, a TORX T 40 key. 1. Remove the front door trim (see " Removal and installation...

Removal and installation the door opening limiter
To remove, replace and install the door opening limiter on a car, you will need: keys "10", "13". 1. Remove the front door trim (see " Removal and installation the front door trim "). 2. Remove the...

Front door glass replacement
To replace the front door glass on your car, you will need: a flat-blade screwdriver and a 10 mm spanner. 1. Lower the glass to the lowest position. 2. Remove the front door trim (see " Removal and...

Removal and installation the front door
To remove and install the front door on the car you will need: a 10 mm socket wrench, a TORX T40 wrench. 1. Disconnect the wire from the negative terminal of the battery. 2. Disconnect the door...

Removal and installation the rear door trim
To remove and install the rear door trim on a car, you will need: a knife, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery. 2. Pry up the...

Replacing the central lock of the rear door
To replace the central rear door lock on your car, you will need: an 8 mm socket wrench, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery. 2....

Removal and installation the outer rear door handle
To remove and install the outer handle of the rear door on a car, you will need an 8 mm socket wrench. 1. Remove the rear door trim (see " Removal and installation the rear door trim "). 2. Remove...

Removal and installation the rear door window regulator
To remove and install the rear door window regulator on a car, you will need an 8 mm socket wrench. 1. Remove the rear door trim (see " Removal and installation the rear door trim "). 2. Position the...

Removal and installation rear door glass
To remove and install the rear door glass on a car, you will need: a knife, an 8 mm socket wrench, and flat- and Phillips-head screwdrivers. 1. Remove the rear door trim (see " Removal and...

Removal and installation the rear door
To remove and install the rear door on the car you will need: a 10 mm socket wrench, a TORX T40 wrench. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the door wiring...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Body and interior: Doors, locks and windows Lada Granta 1 (2011-2023, VAZ-2190)
• Body and interior: Doors, locks and windows Lada Priora 1 (2007-2018, VAZ-2170)
• Body and interior: Doors, locks and windows Lada Vesta 1 (2015-2023, VAZ-2180)
• Body and interior: Doors, locks and windows Lada Largus 1 (2012-2023)

Link to this section in various formats

TEXTHTMLBB Code