Car gearbox Lada Kalina 1

Design features, gearbox device
The car is equipped with a five-speed gearbox, combined with a differential and final drive. Primary shaft 29 (figure 5.2) the gearbox is designed as a block of drive gears, which are in constant...

itemprop="image"

Gearbox malfunctions, their causes and solutions
Cause of malfunction Method of elimination Noise in the gearbox Wear of gear teeth in the gearbox Bearing wear Low gearbox oil level Replace worn parts Replace worn bearings Add oil to the gearbox....

Gearbox oil change
The vehicle manufacturer recommends changing the gearbox oil every 75,000 km. To change the oil in the gearbox of a car, you will need: a 17 mm wrench, a syringe for filling transmission units or a...

Replacing gearbox seals
For replacement on the car seals of internal constant velocity joints (CV joints) drain the oil from the gearbox (see " Gearbox oil change "). 1. Disconnect the front wheel drives from the gearbox...

Removal and installation the gearbox
To remove and install the gearbox on a car, you will need: keys "10", "13", "17", "19", TORX T14, a large flat-blade screwdriver or a mounting blade. 1. Disconnect the wire from the negative terminal...

Disassembly and assembly of the gearbox and defect detection of its parts
Attention! If during the gearbox repair process at least one of the following parts was replaced: clutch or gearbox housings, differential housing or differential bearings, then it is necessary to...

Repair of the secondary shaft of the gearbox
The secondary shaft parts are shown in the figure 5.5. To repair the secondary shaft of the gearbox on a car, you will need: two large flat-bladed screwdrivers, a hammer, a soft metal punch, and a...

Repair of the primary shaft of the gearbox
The primary shaft is a block of drive gears, one part of which is made on the primary shaft, and the second is pressed in with great tension. Therefore, the primary shaft of the gearbox is a...

Gearbox synchronizer repair
To repair the gearbox synchronizer on a car, you will need: a flat-blade screwdriver, pliers with thin jaws. 1. Remove the synchronizer from the secondary shaft (see " Repair of the secondary shaft...

Differential repair
Figure 5.6. Differential: 1 - speed sensor setting ring; 2 - satellite; 3 - axle gear; 4 - driven gear of the main transmission; 5 - satellite axis; 6 - differential housing; 7 - differential bearing...

Selecting the differential bearing adjusting ring
The preliminary tension of the differential bearings should be 0.15-0.35 mm. The tension of the differential bearings is ensured by selecting the thickness of the adjusting ring from those supplied...

Replacement of axle bushings and repair of the ball joint of the gearshift lever
If the gears on the car have become unclear, the overall travel of the gear shift lever has increased and the lever vibrates while the car is moving, the gear shift lever axle bushings or their...

Adjusting the gearbox control drive
To adjust the gearbox control drive on a car, you will need: a 13 mm wrench and a screwdriver. 1. From underneath the Lada Kalina, loosen and unscrew the nut of the clamp bolt on the gearbox control...

Replacing the reverse gear lock solenoid
The reverse gear lock solenoid on a vehicle is an element of the electrical system, but since it is functionally related to the gearbox control drive, its replacement is described in this subsection....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Transmission: Car gearbox Lada Granta 1 (2011-2023, VAZ-2190)
• Transmission: Car gearbox Lada Priora 1 (2007-2018, VAZ-2170)
• Transmission: Mechanical gearbox Lada Vesta 1 (2015-2023, VAZ-2180)
• Transmission: Car gearbox Lada Largus 1 (2012-2023)
• Transmission: Transmission Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code