Lada Kalina 1 car engine power system

Power supply system reference data
Table 8.3.1. Basic data for monitoring, adjustment and maintenance Table 8.3.2. Tightening torques for threaded connections

Description of the power supply system design
The fuel system consists of a fuel tank, fuel module, fuel filter, fuel rail with injectors, air filter, fuel lines, air ducts, throttle assembly, intake module, and a gasoline vapor recovery system....

Checking the technical condition of the power supply system
To perform the work you will need a special fuel pressure gauge. Sequence of execution 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Unscrew the protective...

Air filter — replacing the filter element
According to the manufacturer's recommendation, we replace the air filter element after every 30,000 km. Sequence of execution 1. Prepare the car for repairs (see " Preparing the car for maintenance...

Air filter — removal and installation
The operation may be required when repairing the engine and its systems. Therefore, in many cases it is advisable to remove the filter together with the mass air flow sensor and even with the air...

Throttle valve — drive adjustment
It is necessary to adjust the throttle drive after replacing the drive cable, after removing and installing the throttle assembly, and also after performing work related to dismantling the intake...

Throttle Cable Replacement
The throttle cable is replaced if it is stuck in the casing or damaged. Warning! Work should only be started after the engine has cooled to a safe temperature (not higher than 45°C). Removal 1....

Throttle assembly — removal, gasket replacement and installation
Tip: The throttle body can be removed without draining the coolant. This will require two M12 bolts of any length. Warning! Work should only be started after the engine has cooled to a safe...

Intake module — removal and installation
We dismantle the intake module to check the injectors when it is necessary to remove the fuel rail, as well as in other cases when repairing the engine. To carry out the work, you will need an...

itemprop="image"

Fuel Line — Pressure Relief
Sequence of execution 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Remove the fuel pump circuit fuse (see " Engine Management System Fuses and Relays -...

Fuel filter — replacement
To carry out the work, you will need an inspection pit or overpass. Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Relieve the fuel pressure (see...

Fuel rail — removal and installation
The fuel rail is dismantled to remove the injectors, as well as in other cases during engine repair. Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2....

Fuel module — removal and installation
Removal 1. Prepare the car for work (see " Preparing the car for maintenance and repair "). 2. Relieve the fuel pressure (see " Fuel Line - Pressure Relief "). Warning. After releasing the pressure,...

Fuel Level Gauge Sensor — Replacement
Advice: Malfunctions of the fuel level indicator sensor are most often associated with wear of the contact part of its rheostat. This can be verified by measuring its electrical resistance with an...

Fuel Pressure Regulator — Replacement
If you suspect that the pressure regulator is faulty, it must be replaced. Removal 1. Remove the fuel module (see " Fuel module - removal and installation "). 2. Disconnect the wire tip from the fuel...

Fuel module mesh filter — cleaning
One of the reasons for low fuel pressure in the fuel rail may be a dirty mesh filter of the fuel module. Removal 1. Remove the fuel module (see " Fuel module - removal and installation "). 2. Remove...

Fuel pump — replacement
Advice: Pump replacement operation requires experience and precision (fuel module components may be damaged), therefore, in case of a fuel pump failure, it is recommended to replace the fuel module...

Fuel tank — removal and installation
To complete the work you will need an assistant, as well as: inspection ditch or overpass; fuel transfer hose. Note: You can do without an assistant. In this case, a height-adjustable support or...

Fuel Evaporative Recovery System — Removal and Installation
The fuel vapor recovery system consists of an adsorber, a separator, an adsorber purge valve and a gravity valve. The gravity valve is installed on top of the separator. The canister is mounted on...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Power unit: Supply system Lada Granta 1 (2011-2023, VAZ-2190)
• Power unit: Supply system Lada Priora 1 (2007-2018, VAZ-2170)
• Power unit: Supply system Lada Vesta 1 (2015-2023, VAZ-2180)
• Power unit: Supply system Lada Largus 1 (2012-2023)
• Power unit: Fuel system Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code