Interior (internal body elements) Lada Kalina 1

Removal and installation the front seat
The front seats are mounted on runners, the guides of which are attached to brackets on the body floor. To remove and install the front seat on a car, you will need an 8 mm socket wrench. 1. Move the...

Replacing the front seat runners
To replace the front seat runners on your car, you will need an 8 mm socket wrench. 1. Remove the front seat (see " Removal and installation the front seat "). 2. Slide the slide to access the rear...

Removal and installation the rear seat
To remove and install the rear seat on a car, you will need: a flat-blade screwdriver and a 10 mm socket wrench. Note: This work is described for the left side of the rear seat, the right side of the...

Removal and installation of floor tunnel linings
To remove and install the floor tunnel trim on your vehicle, you will need a flat-head and Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the...

Replacing the front seat belt
Warning! The vehicle's seat belts must be replaced if they are torn, frayed, or have been subjected to critical stress in an accident. To replace the front seat belt on your car, you will need: a...

Replacing the rear center seat belt
Warning! The seat belts on your vehicle must be replaced if they are torn, frayed, or have been subjected to a critical load in an accident. To replace the rear center seat belt on a car, you will...

Replacing the rear side seat belt
Warning! The seat belts on your vehicle must be replaced if they are torn, frayed, or have been subjected to a critical load in an accident. To replace the rear side seat belt you will need: a...

Removal and installation the interior rearview mirror
To remove, replace and install the interior rearview mirror on your vehicle, you will need a flat-blade screwdriver. 1. Loosen the interior rearview mirror bracket fixing screw halfway... 2. ...slide...

Removal and installation sun visors
To remove and install sun visors on your vehicle, you will need a Phillips-head screwdriver. Note: This work is shown on the left sun visor, the right sun visor is removed in the same way. 1. Remove...

Removal and installation the handle above the door
To remove, replace and install the handle above the door on a car, you will need: flat-head and Phillips-head screwdrivers. 1. Remove the left and right door handle mounting screw plugs. 2. Remove...

Removal and installation steering column trim covers
To remove and install the steering column trim covers on your vehicle, you will need: flat-head and Phillips-head screwdrivers. 1. Remove the seven screws securing the casing to the steering column...

Removal and installation the front pillar trims
To remove and install the front pillar trims on your vehicle, you will need a flat-blade screwdriver or a knife. 1. Pry up the front pillar trim and, overcoming the resistance of the three plastic...

Removal and installation the center pillar trims
To remove and install the center pillar trims, you will need: a flat-blade screwdriver and a 17 mm spanner. 1. Remove the front and rear door sill trims (see " Removal and installation door sill...

Removal and installation the luggage compartment shelf
To remove and install the luggage rack, you will need a flat-blade screwdriver. 1. Use a screwdriver to pry up and remove the three plastic holders of the luggage compartment shelf from the holes. 2....

Removal the rear pillar trims
To remove the rear pillar trims you will need: flat-head and Phillips-head screwdrivers. 1. Remove the luggage compartment shelf (see " Removal and installation the luggage compartment shelf "). 2....

Removal and installation door sill trims
To remove and install door sill trims on your vehicle, you will need a Phillips screwdriver. 1. Remove the top screw... 2. ...and four lower screws securing the front door sill trim to the body... 3....

Removal and installation the instrument panel
To remove and install the instrument panel on a car, you will need: a flat-blade screwdriver, 10 and 13 mm wrenches, 10 and 13 mm socket wrenches. 1. Disconnect the wires from the battery terminals...

Disassembly and assembly of the instrument panel
Instrument panel console trim removed to access the heater control lever unit, the anti-theft system control unit and to replace the backlight lamps. To disassemble and assemble the instrument panel...

Replacing the air inlet filter
The car is equipped with a liquid-type heater, integrated with the engine cooling system. The heater radiator is placed in a plastic casing installed in the central part of the instrument panel. A...

Removal and installation the heater radiator
To remove and install the heater radiator on your car, you will need a Phillips-head screwdriver. 1. Remove the instrument panel (see " Removal and installation the instrument panel "). 2. Remove the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Body and interior: Interior (internal elements) Lada Granta 1 (2011-2023, VAZ-2190)
• Body and interior: Interior (internal elements) Lada Priora 1 (2007-2018, VAZ-2170)
• Body and interior: Interior (internal elements) Lada Largus 1 (2012-2023)
• Body and interior: Interior (internal elements) Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code