Interior (internal body elements) Lada Priora 1

Removal and installation the front seat
You will need: socket wrenches (heads) "13", TORX E10, screwdriver. 1. Move the seat forward as far as it will go, use a screwdriver to remove the ends of the torsion bars from the brackets and...

Removal and installation the rear seat
You will need: a 10 mm spanner and a Phillips-head screwdriver. 1. Press the seat cushion lock handle… 2. …and lift the edge of the pillow. 3. Similarly, free the second edge of the pillow.. 4. …and...

Replacing the front seat belt
Warning! Seat belts must be replaced if they are torn, frayed, or if they have been subjected to critical stress in an accident. Attention! When installing seat belts, use only the standard bolts...

Replacing rear seat belts
You will need: a 17 mm wrench and a flat-blade screwdriver. Rear side seat belt remove in the following order. 1. Remove the rear seat cushion (see "Removing and installing the rear seat" ). 2. Pry...

Removal and installation the interior rearview mirror
You will need a Phillips-head screwdriver. 1. Pry up the front edge of the decorative cover… 2. …and remove the lid. 3. Remove the two mirror mounting screws… 4. …and take it off. 5. Install the...

Removal and installation sun visors
You will need a Phillips-head screwdriver. Note: This operation is shown using the left sun visor as an example; remove the right sun visor in the same way. 1. Remove the outer screw securing the...

Removal and installation handrails
You will need a flat-head and Phillips-head screwdriver. 1. Pry with a screwdriver… 2. …and remove the left and right handrail mounting screw plugs. 3. Remove the mounting screws… 4. …and remove the...

Removal and installation steering column trim covers
You will need a flat-head and Phillips-head screwdriver. Note: For clarity, the operations are shown with the steering wheel removed. 1. Remove the three screws in the front… 2. …two screws in the...

Removal and installation of floor tunnel linings
You will need: a 10 mm wrench, flat-head and Phillips-head screwdrivers. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the screws securing the left and right screens… 3....

Removal and installation the front pillar trims
You will need a flat-blade screwdriver or a knife. 1. Pry up the trim and, overcoming the resistance of the three plastic holders, remove it from the car. 2. Install the trim in the reverse order of...

Removal and installation the center pillar trims
You will need: a 17 mm wrench, flat-head and Phillips-head screwdrivers. 1. Using a screwdriver, remove the upper decorative trim. 2. Remove the upper belt mounting bolt… 3. …and remove the upper...

Removal and installation the luggage compartment shelf
1. Remove the rear seat back (see "Removing and installing the rear seat" ). 2. Disconnect the additional brake light wiring harness connector. 3. Lift up… 4. …and remove the luggage rack from the...

Removal the rear pillar trims
You will need a flat-blade screwdriver. 1. Remove the luggage compartment shelf (see "Removing and installing the luggage compartment shelf" ). 2. Remove the bolt and the upper seat belt anchor loop...

Removal and installation threshold trims
You will need a Phillips-head screwdriver. 1. Remove the two screws securing the front trim… 2. …and remove it, overcoming the resistance of the plastic holders. 3. Remove the rear seat cushion (see...

Removal and installation the instrument panel
Note: You may need to use harness ties when installing the instrument cluster, as they may be easier to cut when removing the cluster in some cases. Note: Depending on the vehicle configuration, a...

Disassembly and assembly of the instrument panel
You will need a flat-head and Phillips-head screwdriver. 1. Remove the three screws securing the windshield deflector… 2. ...and remove the deflector. 3. Remove two screws… 4. …and remove the left...

Features of the heater design
Figure 11.4. Vehicle interior ventilation and heating system: 1 – left side ventilation nozzle; 2 – left ventilation air duct; 3 – side window heating nozzle; 4 – air heating distributor; 5 – heater;...

Removal and installation the heater
You will need: a spanner "8", socket wrenches (head) "10", "13", a screwdriver with a Phillips blade, side cutters. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the...

Removal and installation the heater radiator
If coolant is leaking from the heater, it means the radiator is leaking and needs to be replaced. You will need a Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Body and interior: Interior (internal elements) Lada Kalina Hatchback (2004-2013, VAZ-1119)
• Body and interior: Interior (internal elements) Lada Granta 1 (2011-2023, VAZ-2190)
• Body and interior: Interior (internal elements) Lada Largus 1 (2012-2023)
• Body and interior: Interior (internal elements) Lada X-Ray 1 (2015-2022)

Link to this section in various formats

TEXTHTMLBB Code