Vehicle starting and charging system Lada Priora 1
Features of the battery design
The car is equipped with a lead starter battery with a capacity of 55 Ah. Batteries of this capacity are produced by many different manufacturers, but the characteristics of these batteries are...
The car is equipped with a lead starter battery with a capacity of 55 Ah. Batteries of this capacity are produced by many different manufacturers, but the characteristics of these batteries are...
itemprop="image"Caring for the battery
At least once every two weeks, remove dust and dirt from the surface of the monoblock and battery cover with a dry cloth. If electrolyte accidentally ends up on the lid, remove it with a clean cloth...
At least once every two weeks, remove dust and dirt from the surface of the monoblock and battery cover with a dry cloth. If electrolyte accidentally ends up on the lid, remove it with a clean cloth...
Checking the electrolyte level in the battery
Periodically, at least once every two weeks, check the electrolyte level in the battery cells. Note: For batteries with a common lid for all elements, equipped with a capacitor cavity, it is...
Periodically, at least once every two weeks, check the electrolyte level in the battery cells. Note: For batteries with a common lid for all elements, equipped with a capacitor cavity, it is...
Checking the battery charge level
If during operation there are difficulties with starting the engine, check the state of charge of the battery by the density of the electrolyte or the voltage at its terminals in an unloaded state...
If during operation there are difficulties with starting the engine, check the state of charge of the battery by the density of the electrolyte or the voltage at its terminals in an unloaded state...
Removal and installation the battery
You will need: a 10 mm wrench and a 13 mm socket wrench. 1. Open the hood. 2. Loosen the tightening nut of the end cap clamp bolt... 3. ...and remove the wire from the negative terminal of the...
You will need: a 10 mm wrench and a 13 mm socket wrench. 1. Open the hood. 2. Loosen the tightening nut of the end cap clamp bolt... 3. ...and remove the wire from the negative terminal of the...
Charging the battery
After removing the battery from the vehicle, carefully clean it, especially its upper part, and check the electrolyte level (see "Checking the electrolyte level in the battery" ) and, if necessary,...
After removing the battery from the vehicle, carefully clean it, especially its upper part, and check the electrolyte level (see "Checking the electrolyte level in the battery" ) and, if necessary,...
Design Features of the Generator
The Lada Priora cars are equipped with a generator mod. 5102.3771 AC, three-phase, with built-in rectifier unit and electronic voltage regulator, right rotation (if you look from the drive side). Mod...
The Lada Priora cars are equipped with a generator mod. 5102.3771 AC, three-phase, with built-in rectifier unit and electronic voltage regulator, right rotation (if you look from the drive side). Mod...
Removal and installation the generator
You will need a 13 mm socket wrench. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the alternator drive belt (see "Replacing the alternator drive belt" ). 3. Disconnect...
You will need a 13 mm socket wrench. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the alternator drive belt (see "Replacing the alternator drive belt" ). 3. Disconnect...
Checking and replacing the voltage regulator with brush holder
The generator 5102.3771 is equipped with a voltage regulator mod. 5102.3771.060. The operation of the voltage regulator consists of continuously automatically changing the excitation current of the...
The generator 5102.3771 is equipped with a voltage regulator mod. 5102.3771.060. The operation of the voltage regulator consists of continuously automatically changing the excitation current of the...
Generator repair
You will need: flat- and Phillips-head screwdrivers, 8 and 10 mm wrenches, 8 and 24 mm socket wrenches, a hammer, and a tester. 1. Remove the generator from the vehicle (see "Removing and installing...
You will need: flat- and Phillips-head screwdrivers, 8 and 10 mm wrenches, 8 and 24 mm socket wrenches, a hammer, and a tester. 1. Remove the generator from the vehicle (see "Removing and installing...
Features of the starter design
The starter mod is installed on Lada Priora cars. 2111.3708010-01. Figure 10.3. Starter connection diagram: 1 – starter; 2 – mounting block; 3 – ignition switch (lock); 4 – battery; A – to the main...
The starter mod is installed on Lada Priora cars. 2111.3708010-01. Figure 10.3. Starter connection diagram: 1 – starter; 2 – mounting block; 3 – ignition switch (lock); 4 – battery; A – to the main...
Removal and installation the starter
You will need: open-end wrenches "13", "15". 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the air filter (see "Removing and installing the air filter" ). 3. Unscrew the...
You will need: open-end wrenches "13", "15". 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the air filter (see "Removing and installing the air filter" ). 3. Unscrew the...
Starter repair
Figure 10.4. Starter parts 2111.3708010-01: 1 – body; 2 – thrust ring from the collector side; 3 - anchor; 4 – permanent magnet; 5 – positive polarity brush busbar mounting nut; 6 – traction relay; 7...
Figure 10.4. Starter parts 2111.3708010-01: 1 – body; 2 – thrust ring from the collector side; 3 - anchor; 4 – permanent magnet; 5 – positive polarity brush busbar mounting nut; 6 – traction relay; 7...
Features of the ignition system design
The ignition system does not use a traditional distributor... ...individual ignition coils are used here. The ignition system has no moving parts, so it is maintenance-free and does not require...
The ignition system does not use a traditional distributor... ...individual ignition coils are used here. The ignition system has no moving parts, so it is maintenance-free and does not require...
Removal and installation ignition coils
You will need a 10mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the decorative cover from the engine (see "Removing and installing the decorative engine...
You will need a 10mm socket head. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the decorative cover from the engine (see "Removing and installing the decorative engine...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
More sections with information from manuals for Lada:
• Electrical equipment: Power devices Lada Kalina Hatchback (2004-2013, VAZ-1119)
• Electrical equipment: Power devices Lada Granta 1 (2011-2023, VAZ-2190)
• Electrical equipment: Power devices Lada Vesta 1 (2015-2023, VAZ-2180)
• Electrical equipment: Power devices Lada Largus 1 (2012-2023)
Link to this section in various formats
TEXTHTMLBB Code
- General information
- Vehicle device
- User manual
- Faults en route
- Maintenance
- Power unit
- Engine repair
- Cooling and lubrication system
- Supply system
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Drive shafts
- Chassis (running gear)
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Power devices
- Lighting and signaling
- Cooling and heating
- Electrical circuits