Doors, locks and windows of the car Lada Priora 1

Removal and installation the trunk lid
Note: The trunk lid is quite heavy and bulky, so it is recommended to remove and install it with the help of two people. You will need: wrenches "10", "13", pliers. 1. Disconnect the wire from the...

Removal and installation the trunk lid lock and its drive
You will need: 10 and 13 mm wrenches, 10 and 13 mm socket wrenches (head), flat-head and Phillips-head screwdrivers, pliers. 1. Disconnect the wire from the negative terminal of the battery. 2. Use a...

Adjusting the position of the trunk lid lock
If the trunk lid has vertical play when closed or is difficult to close, adjust the height of the lock. You will need: a socket wrench (head) "on 10", a screwdriver with a flat blade, pliers. 1....

Removal and installation the front door trim
You will need a flat-head and Phillips-head screwdriver. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the two screws securing the inner door handle to the window and...

Removal and installation the front door lock
Figure 11.2. Lock, drive rods and front door handles: 1 – lock switch rod; 2 – lock switch; 3 – lock button rod; 4 – outer handle rod; 5 – outer handle; 6 – inner handle pull; 7 – inner handle; 8 –...

Adjusting the front door lock
If the door closes tightly or loosely, adjust the lock. You will need: an impact screwdriver with a TORX T40 bit, a hammer. 1. Loosen the three screws securing the retainer. 2. Move the latch outward...

Removal and installation the door opening limiter
You will need: a spanner "8", a socket wrench (head) "10". 1. Remove the front door trim (see "Removing and installing the front door trim" ). 2. Using a 10 mm socket wrench, unscrew the two bolts...

Front door glass replacement
You will need a 10 mm wrench. 1. Remove the front door trim (see "Removing and installing the front door trim" ). 2. Pry up the inner glass seal from the inside… 3. …and remove the seal. 4. Pry up...

Replacing the front door window regulator
You will need: a 10 mm wrench, wooden or plastic wedges. 1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front door trim (see "Removing and installing the front door...

Removal and installation the front door
You will need: socket wrenches (heads) "10", "13". Note: The door is quite heavy and bulky, so we recommend removing and installing it with an assistant. When replacing a door, remove all hardware...

Removal and installation the rear door trim
You will need a flat-head and Phillips-head screwdriver. 1. Use a thin screwdriver to pry the window lift handle lock away from the socket. 2. Slide the retainer so that the protrusion on it...

Removal and installation the rear door lock
Figure 11.3. Lock, drive rods and rear door handles: 1 – outer handle rod; 2 – outer handle; 3 – intermediate locking rod; 4 – intermediate lock lever; 5 – lock button pull; 6 – inner handle; 7 –...

Removal and installation the outer rear door handle
You will need: a socket wrench (head) "8", a screwdriver with a flat blade. 1. Remove the rear door trim (see "Removing and installing the rear door trim" ). 2. Use a screwdriver to pry up and...

Rear door glass replacement
You will need a socket wrench (head) "on 10". 1. Remove the rear door trim (see "Removing and installing the rear door trim" ). 2. Remove the door trim. 3. Pry it from the inside and remove the inner...

Replacing the rear door window regulator
You will need: keys "8", "10", wooden or plastic wedges. 1. Remove the rear door trim (see "Removing and installing the rear door trim" ). 2. Raise the glass so that you can access the glass frame...

Removal and installation the rear door
You will need: socket wrenches (head) "8", "10". Note: The door is quite heavy and bulky, so we recommend removing and installing it with an assistant. When replacing a door, remove all hardware from...

Replacement of fixed body glazing
You will need: a screwdriver, an awl, a knife, and a glass gluing kit. This is what the glass gluing kit looks like. It consists of a tube of glue, a tube tip, an activator/cleaner and a primer....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections with information from manuals for Lada:

• Body and interior: Doors, locks and windows Lada Kalina Hatchback (2004-2013, VAZ-1119)
• Body and interior: Doors, locks and windows Lada Granta 1 (2011-2023, VAZ-2190)
• Body and interior: Doors, locks and windows Lada Vesta 1 (2015-2023, VAZ-2180)
• Body and interior: Doors, locks and windows Lada Largus 1 (2012-2023)

Link to this section in various formats

TEXTHTMLBB Code