Front suspension — design description The front suspension is independent with telescopic hydraulic shock absorbers and coil springs. The front suspension consists of stamped lower wishbones and an anti-roll bar attached to the front...
Car suspension recommendations It is recommended to check and, if necessary, adjust the alignment of the front wheels every 10-15 thousand km. These are important parameters on which the stability of the car, driving comfort and...
Swivel fist and front suspension hub — removal and installation Note. part numbers for this assembly see here hub assembly (rounded fist) from the inside in the removed state: 1 – a rotary fist; 2 - front hub bearing; 3 - adjusting ring of the speed sensor; 4 -...
Front wheel bearing — removal and installation Note. bearing catalog number see here . 1 - steering knuckle; 2 — an adjusting ring of the gauge of speed of rotation of a wheel (on a car without ABS); 3 - hub bearing; 4 - retaining ring; 5 - wheel...
Bearing fault diagnosis and installation The information on this page is general for cars of any make and model year. Modern bearings are designed for a long service life. For example, under ideal operating conditions, the resource of wheel...
Front shock absorber strut — removal, disassembly and replacement see also Removal, disassembly and repair of the front shock absorber . Note. For Largus Cross modifications, the suspension struts differ from the usual Universal. This must be taken into account...
Removal, disassembly and repair of the front shock absorber see also Removal and installation of a rack of a forward shock-absorber . Shock absorber front: 1 - telescopic stand; 2 - spring; 3 - compression stroke buffer with a protective cover; 4 - nut for...
Shock absorber defects — manifestation and causes The information on this page is general for cars of any make and model year. External manifestation of a malfunction / breakdown / problem: Corrosion of the shock absorber support bearing, creaking...
Ball joint of the front suspension arm — removal and installation Attention. The ball joint of the front suspension arm may only be replaced once. For this, ball joints from spare parts are marked with the letter "R" and are equipped with a retaining spring 4,...
Front suspension subframe — removal and installation Removing The work is done on a lift. Secure the engine radiator to the front cross bar of the engine compartment with straps. Remove the front wheels and engine crankcase protection. Remove the front...
Anti-roll bar front suspension — removal and installation Figure 8-1 - Front anti-roll bar: 1 - a bolt of fastening of an arm of a pillow of the stabilizer (subframe mounting bolt); 2 - nut for attaching the stabilizer cushion bracket; 3 - stabilizer bar; 4...
Rear suspension — design description Rear suspension with coil springs, double-acting telescopic hydraulic shock absorbers and trailing arms elastically connected by a transverse beam and anti-roll bar. The rear wheel hub is made in the...
Rear suspension shock absorber — removal and installation Note. rear shock absorber part numbers see here . Note. When choosing spare parts, keep in mind that the shock absorbers installed on the Cross modification differ in size from those installed on the...
Rear suspension spring — removal and installation Suspension springs are divided into classes (by hardness) and are labeled accordingly. (For example, the springs installed on the Van modification have a reinforced structure compared to conventional...
Rear wheel hub bearing — check, removal and installation The rear wheel hub is integrated with the brake drum and mounted on a double-row ball bearing. Note. bearing and part numbers see here . Rear wheel bearing assembly: 1 - trunnion; 2 - brake drum; 3 -...
Rear wheel hub axle — removal and installation Removing Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition. Remove rear wheel: remove the brake drum from the axle of the rear wheel hub; disconnect the manual...
Rear suspension arms — removal and installation Figure 6-1 - Rear suspension: 1 - rear suspension shock absorber; 2 - plug; 3 - upper spring gasket; 4 rear suspension spring; 5 - lower spring gasket; 6 - axle of the rear wheel hub; 7 - rear...
Rear suspension arm joints (silent blocks) — replacement Removing Place the vehicle on a two post lift and turn off the ignition. Remove rear wheels. Remove the rear wheel speed sensor harnesses from the holders on the rear suspension arms. Unscrew the...
Wheel — removal and installation see also Spare wheel . Removing Place the vehicle on a two-post lift, apply the parking brake and turn off the ignition. Remove wheel trim (flat screwdriver). Loosen the wheel bolts, while the car...
Front wheel alignment Figure 10 - Adjusting the toe of the front wheels of LADA LARGUS R90 and F90 cars: 1 - locknut for adjusting wheel alignment; 2 - steering trapezoid linkage Table 1 Automobile model Tire size Air...