2. Car stands, adjustable in height and with a permissible load of at least 1 ton. It is advisable to have four such stands.
3. Wheel chocks (at least 2 pcs.).
4. Double-ended wrenches for 8 and 10 mm brake system nipples. The two most common types of such wrenches are a clamp wrench and a slotted open-end wrench. The clamping key allows you to unscrew fittings with worn edges. In order to put the key on the brake pipe nipple, it is necessary to unscrew the clamping bolt. A slotted open-end wrench allows you to perform work more quickly, but such a wrench must be made of high-quality steel with appropriate heat treatment.
5. Special key for tensioning the timing belt.
6. A 24mm octagonal head wrench for disassembling the steering gear.
7. Flat ratchet with removable tips. Can be used in hard to reach places as a flat reversible screwdriver.
8. Piston ring pullers. There are two types of such pullers: for extracting retaining rings from holes and for removing retaining rings from shafts, axles, rods. Such pullers come with straight and curved jaws.
9. Special keys for installing clamps for CV joint protective covers.
10. Puller for pressing out ball joint pins and steering rod ends.
11. Oil filter remover.
12. Universal three-jaw pullers for removing pulleys, hubs, gears.
13. Universal pullers with narrow jaws for removing couplings, gears, bearing rings. The design of the puller allows for combination by installing two or three grips.
14. Set of tools for replacing hub bearings. The kit includes a puller for removing the inner bearing ring and a device for extracting and pressing in hub bearings.
15. Universal cup puller for extracting and pressing in hub bearings and rubber-metal hinges (silent blocks) levers.
16. Puller and mandrel for replacing oil scraper caps.
17. Set for compressing springs and dehydrating valves of the gas distribution mechanism.
18. Device for grinding valves.
19. Special 22 mm open-end or socket wrenches for unscrewing the oxygen concentration sensor.
20. Tweezers.
21. Suspension spring clamps.
22. Impact screwdriver with a set of attachments.
23. Digital multimeter (tester) for checking sensors and electrical circuits.
24. A special 12V probe or test lamp for checking the electrical circuits of the vehicle that are under voltage.
25. Tire pressure gauge (if there is no pressure gauge on the tire pump).
26. Pressure gauge for measuring pressure in the engine fuel rail.
27. Pressure gauge for checking the pressure in the engine lubrication system.
28. Compression gauge for checking the pressure in the engine cylinders.
29. Bore gauge for measuring the diameter of cylinders.
30. Caliper with depth gauge.
31. Micrometers with measurement ranges of 0-25, 25-50 and 50-75 mm.
32. A set of round feeler gauges for checking the gap between spark plug electrodes.
33. A set of flat feeler gauges for measuring gaps when assessing the technical condition of units.
34. Mandrel for centering the driven clutch disc.
35. Technological mandrel for fixing the differential axle gear. The mandrel is installed in the gearbox hole after both drives have been removed to prevent the axle gears from falling out of the differential.
36. Mandrel for compressing piston rings.
37. Hydrometer for measuring liquid density (electrolyte in the battery or antifreeze in the expansion tank).
38. A special device with metal brushes for cleaning wire terminals and battery terminals.
39. Magnet on a telescopic pointer for extracting small metal objects from hard-to-reach places.
40. Oil syringe for filling oil into the gearbox housing.
Note: Since the gearbox oil is rarely changed and is poured in from above through the level indicator hole, a funnel with a 50-60 cm long plastic tube attached to it can be used instead of an oil syringe.
41. Hose with a bulb for pumping fuel. Hoses can be used to drain fuel from the tank before removing it.
42. Wide and narrow locksmith (metal) rulers for checking planes.
43. Device for disassembling suspension struts. The device consists of two elements: the inner element is designed to hold the shock absorber rod (by 6 and 10 mm), and the outer one is for unscrewing its nut (17 and 22 mm).
44. Technical hair dryer (heat gun). Necessary for heating parts during assembly and disassembly (for example, heat shrink tubing when repairing electrical wiring).
45. When performing the work, you may also need: a clamp, tape measure, household spring balance, a wide container for draining oil and coolant with a capacity of at least 10 liters, a medical syringe or a bulb for collecting liquid.