Removal
Place the vehicle in the work area, lower the window to the lower position, and disconnect the ground wire terminal from the battery.
Loosen screw 2, Figure 4-1, securing the inner door handle 3; disconnect the lock rod from the handle, remove the handle (torx T30 screwdriver).
Remove the trim and unscrew the four self-tapping screws 4 securing the speaker of the acoustic system, disconnect the wiring harness connector and remove the speaker.
Figure 4-1 - Disassembling the front door: 1 - front door trim; 2 - screw for fastening the handle of the inner front door; 3 - front door handle inside; 4 - self-tapping screw for fastening the loudspeaker of the acoustic system
Unscrew the self-tapping screw 4, Figure 4-3, securing the upholstery from the end.
Unscrew the self-tapping screw 2 securing the upholstery to the armrest.
For the version with a manual window lift: move cover 1, Figure 4-2, window lift handles away from the door trim, remove retaining bracket 2, remove handle 3.
Figure 4-2 - Removing the window handle: 1 - window lift handle cover; 2 - fixing bracket; 3 - window lift handle
Overcoming the resistance of the holders, detach the trim 1 (see figure 4-1) from the door, remove button 3, Figure 4-3, from the hole in the upholstery, locking the lock.
Figure 4-3 - Fastening the trim from the end: 1 - horizontal glass seal; 2 - self-tapping screw for fastening the upholstery on the armrest; 3 - door lock button; 4 - self-tapping screw for fastening the trim from the end
Remove seals 1.
Temporarily connect the ground wire terminal to the battery (for the version with manual window lift: temporarily put on the handle), raise the glass until the window lift slider is positioned opposite the opening in the inner door panel.
Holding the glass, unscrew the two screws 2, Figure 4-4, securing the glass clip 1 to the slider, and remove the glass from the door.
Figure 4-4 - Fastening the glass clip to the window lifter slider: 1 - front door glass; 2 - screws for fastening the glass clip to the window lifter slider; 3 - window lift slider
Unscrew three nuts 4, Figure 4-5, remove window lifter 5 through the opening in the door panel, disconnecting the wiring harness block from it (10 mm spanner).
Unscrew two screws 2, remove safety buffer 3 through the opening in the door panel.
Figure 4-5 - Window regulator mounting: 1 - screw for fastening the front door molding; 2 - screw for fixing the safety buffer; 3 - safety buffer; 4 - window regulator mounting nut; 5 - front door window lifter
Unscrew two nuts 1, Figure 4-6, remove the outer handle 2, disconnecting the door lock rods from it (10 mm spanner).
Figure 4-6 - Fastening the outer handle: 1 - outer handle fastening nut; 2 - outer handle of the front door
Remove spring clip 2, Figure 4-7, securing switch 3 of the front door lock, remove the switch, disconnecting the lock rods from it.
Figure 4-7 - Fastening the front door lock cylinder: 1 - glass guide; 2 - spring clamp for fastening the cylinder; 3 - lock switch
Unscrew the three screws 1, Fig. 4-8, securing the lock 2 of the front door, remove the lock, disconnecting the wiring harness block from it (torx T30 screwdriver).
Loosen screw 3, remove guide 1 (see figure 4-7).
Loosen screw 4, fastening molding 2, Figure 4-9, overcoming the resistance of the holders, remove the molding.
Figure 4-8 - Front door lock mounting: 1 - screw for fastening the front door lock; 2 - front door lock; 3 - screw for fastening the front door glass guide; 4 - screw for fastening the front door molding
Figure 4-9 - Door moldings and outside rearview mirror: 1 - outside rear view mirror; 2 - Front door molding; 3 - rear door molding
Unscrew the two bolts 1, Figure 4-10, securing the outside mirror 1 (see figure 4-9) rear view, remove the mirror.
Figure 4-10 - Rearview mirror mounting: 1 - rear view mirror mounting bolt
Unscrew the two nuts 3, Figure 4-11, securing the limiter 2 to the door (replacement head 10, ratchet).
Remove the protective cover, 4 wire harnesses and wire harness from the door.
Unscrew the four nuts 1 securing the door to the hinge, remove the front door (the operation should be performed with an assistant) (spanner 13).
Figure 4-11 - Front door mounting: 1 - door fastening nut to the hinge; 2 - door opening limiter; 3 - nut for fastening the limiter to the door; 4 - protective cover for wiring harness
Installation
Location of the left front door trim fastening clips (view from the inside)
Install door components and parts in the reverse order of removal, while:
- lubricate the rubbing parts of the window lifter, sliding surfaces in the door lock, door opening limiter, rod joints and hinges (cIATIM-201 grease, consumption rate -5 g);
- before installing the trim, connect the ground wire terminal to the battery, check and, if necessary, adjust the operation of the door lock, check the operation of the window lifter, and lift the window up;
- if necessary, restore or replace the sealing gasket on the end of the trim;
- ensure a uniform gap between the door and the mating body panels.
Original is available on this resource www.Ladaman.ru